Products
Product Showcase
Used Equipment
Services
News
Employment
About Us
Contact Us
Home
 
Showcase



2017 Ford F550 with Maintainer Service Body and 6520TT Crane
SP060
Model MTS-1-084:
52" High X 23" Deep Compartments, Length 11'

Call Hews Sales Team at: 1-800-234-4397!
STANDARD FEATURES:
  • A60 Galvannealed steel body
  • 12 GA shell, bulkhead and wheel skirting
  • 3/16" Aluminum exterior doors
  • Gas shock door hold backs
  • Full length aluminum drip rail
  • Reinforced compartment floors
  • Door locks with "D"-ring handles and three point rolling sure lock latches
  • 49" Wide center deck overlaid with steel deck plate
  • 4-Flush mount "D" ring tie downs
  • 10" Swing down tailgate
  • Fully primed and undercoated


  • COMPARTMENT EQUIPMENT:
  • Adjustable shelving package: two shelves in vertical compartments, one shelf in each horizontal compartment
  • 59" OXY/ACT bottle storage compartment
  • Two Blowers w/Filters for Pressurized Storage System
  • Welder Mount Angles on Top of Compartment
  • Dualock Aluminum 5 drawer set and 7 drawer set


  • BUMPER:
  • 26" Work bench bumper with doors on both ends
  • Full width transverse storage compartment
  • Two vise mount sockets
  • One vise mounting plate
  • LED Sealed recessed tail and marker lights
  • Built in access step
  • 2" Square - class IV receiver


  • HYDRAULIC SYSTEM:
  • Closed center - load sensing power pack
  • Oil reservoir with in tank filter, vented cap, suction screen sight and temperature gauge and gate valve
  • Flip up cover over rear manual controls


  • CRANE: Model 6520TT - 6,500 lb Maximum Capacity - mount curbside rear
  • Hydraulic extend from 10' to 20'
  • Anti-two block, holding valves, and overload protection
  • Adjustable boom saddle
  • Engine start/stop on remote
  • Two rear outriggers, hydraulic down, manual out, crane side
  • Wireless proportional remote control

  • Contact our Sales Team




    Stellar Model 120-16-20 Hooklift
    Installed on 2018 Kenworth T370
  • Lift/dump capacity 20,000 lbs
  • 48 degree dump angle (with optimum length body)
  • 54" hook height
  • Single 4" double acting lift cylinder w/integral counterbalance valve
  • Single 3,5" double acting tilt cylinder w/integral counterbalance valve
  • Dump tilt interlock, dual fixed position body hold down devices/rear
  • Loader height approximately 8.38" from top of frame to top of rollers
  • All hose and tubing are SAE (US fittings)
  • High pressure lift and jib system(4,200 psi)
  • AIR controls to operate hoist,control valve mtd on oil reservoir
  • PTO with direct coupled pump (if space allows)
  • Poly fenders
  • Heavy duty rear bumper, w/lights, and reinforced for pintle hitch
  • Installed weight 2,800 lbs - 1 year warranty
  • Pioneer HR1500EAL Tarp system

  • Contact our Sales Team




    Liftmoore Service Body with 3055DXP Crane
    Installed on 2014 DODGE 5500 4X2 REG CAB
    Call for Pricing and/or to schedule a Demo!
  • 40,000 ft-lbs. crane ready service body
  • 132" long, 94" wide, 44" high with 22" compartment depth
  • 50" load area
  • 63" tall from compartment, with 2 bottle holder
  • LED lights
  • 42" hydraulic out & down outrigger curbside; Hydraulic down only outrigger streetside
  • 25 gallon hydraulic oil reservior, mounted in cargo area


  • BODY CONSTRUCTION: S/N A29192
  • 12 ga. galvannealed front, rear and bottom compartment panels
  • 12 ga. tread plate compartment tops, load area walls and front bulkhead
  • 14 ga. A60 galvannealed fenders, door facings and tailgate
  • Holes for recess lights punched high in rear panel and in crane support box with additional support plates
  • Interior support for underside of boom support mounting

  • FLOOR:
  • 1/8" medium pattern tread plate floor with reinforced understructure
  • 6 tie-down rings, floor mounted, folding recessed, capacity 2,000 lbs. each

  • UNDERSTRUCTURE:

  • Front, rear and rear extension cross members 5" x 3"x 3/16" tubing
  • 5" high 3/16" formed intermediate cross members
  • 5" high 6/7# structural steel from extension cross members
  • 3 full length formed 12 ga. steel "C" channel longitudinals
  • 1/2" steel flat bar long runners
  • Automotive grade undercoating

  • DOORS:

  • Double panel doors with 14 ga. galvanneal steel outer panel and 18 ga. corrugated inner panel
  • Door design includes a knife edge for continuous positive contact with door seal
  • Stainless steel 3-point D-Ring latch assembly
  • Stainless steel 5/16" diameter rod hinge pins, stainless steel pillow block hinges, self-lubricating plastic bushings
  • Spring loaded door retainers on vertical doors, chain supports on horizontal doors
  • Master lock, spring loaded return to the open position

  • TAILGATE:

  • Slam latch tailgate with 12 ga. tread plate overlay and center release stainless latch
  • Tailshelf with compartments and 8" deep treadplate step with ball hook recess

  • DRAWERS & SHELVING:

  • Adjustable shelving, all galvannealed steel
  • 3 vertical compartments, 2 horizontal with 15 dividers
  • Drawer units: 31" tall, 34" wide, 20" deep - 2 each: 3", 6", 9"
  • Compartment behind driver with dividers. 250 lb capacity each

  • CRANE: Model 3055DXP - S/N 15-1902W172
  • 5,500 lb Maximum Capacity - mount curbside rear
  • Planetary gear winch - single line speed 31 fpm at 6 gpm
  • Proportional hydraulic control system standard
  • Wireless radio remote control with E-stop and audible signal
  • Galvanized aircraft cable 3/8" x 95 ft. (14,400 lb breaking strength)
  • Traveling block with roller bearing swivel safety hook
  • Power rotation - unlimited
  • Boom elevation - Full Power (-5 deg. to 75 deg); Boom extension - Full Power 10 ft. -20 ft.
  • Counter balance valve
  • Overload protection system
  • Anti-two block system
  • Meets 29 CFR 1910.180 ANDI B30.5, SAE J1063
  • Mounting plate is 16 3/4" square with a 14 3/4" square bolt pattern

  • AIR COMPRESSOR: VANAIR AIR N ARC I300 ALL-IN-ONE, S/N: 30-89791

  • 40 CFM at high speed, 30 CFM at idle
  • 25 HP, liquid cooled
  • Rotary screw
  • Generator: 6,800 continuous watts, 120V GFCI and 240V outlets
  • Hydraulic Output up to 10.5 gpm
  • Welder: 300 amps high frequency CC/DC, CV/DC
  • Dimensions: 21"W x 47"L x 33"H

  • CHASSIS SPECIFICATIONS:

  • 2014 Dodge 5500
  • 6.7 Cummins Turbo Diesel
  • 6-speed automatic transmission
  • Regular Cab 4 X 2
  • Current Mileage: 62,000 miles

  • Contact our Sales Team


    AERO Conestoga
    Call Hews Sales Team at: 1-800-234-4397
    Aluminum Diamond Plate Platform Body with Aero Conestoga Sliding Tarp System
  • 16' long x 96" wide Platform Body
  • Fixed Front - rolls front to rear
  • Roll-up rear curtain
  • Panelized tarp system - 8' sections
  • Uplift bars with spring shocks
  • Stainless steel track with steel wheels
  • Built-in side bump rail
  • 84" inside height
  • Rear tensioning system

  • Contact our Sales Team


    Moffett Mounty Truck Mounted Forklift Model M5000
    Factory Rebuilds
    Click on "Products", "Used Equipment" for more details
    Immediate Availability!
    Call for Pricing!
    New Models Also Available!

    Contact our Sales Team

     
    Copyright 2017 Hews Company LLC - Page design by Spokane Computer Inc.